Mixer is a construction equipment used very much in the construction, but in the work, the concrete mixer often occurs the phenomenon of concrete solidification in the mixer, once this situation occurs, it will affect the normal operation of the concrete mixer to a large extent. How to deal with the concreting of the mixer? This is a problem that many construction parties want to know.

　　中科聚峰攪拌機建議指出：混凝土凝結在攪拌機罐里面的緣由有很多，除了沒有及時清洗外，其中更主要的原因是攪拌機發動機不能運作，由于沒有動力輸入液壓機而招致液壓機中止工作，使得裝料罐不能轉動而讓混凝土凝結在攪拌機罐里面。

　　Zhongke Jufeng mixer suggests that: there are many reasons for the concrete to coagulate in the mixer tank. In addition to not cleaning in time, the main reason is that the mixer engine can't operate. Because there is no power input hydraulic press, the hydraulic press stops working, so that the charging tank can't rotate and the concrete can coagulate in the mixer tank.

　　攪拌機的混凝土凝固了怎么處理？現在給大家介紹兩種方法：

　　How to deal with the concreting of the mixer? Here are two solutions:

　　方法一：風炮

　　Method 1: air cannon

　　如果攪拌機內的混凝土已經凝固，建議可以用“風炮”打碎已經凝結的混凝土，然后一點點鏟出來！通常罐體下部要割開一個口，然后加翻開一個原來就有用羅絲上緊的封蓋，這個蓋是讓有需求進去工作時翻開通風和緊急情況放料的。在打罐過程中人在罐里面要通風，在裝料罐入口應放臺風扇吹風進去，而“風炮”工作時會起灰塵，又要接上水管淋濕打碎的混凝土。把罐里面的混凝土打碎鏟出以后再把割開部分焊接上，上回封蓋，裝滿水試下轉動能否正常，然后少量裝料遞增看液壓機工作能否正常，如果一切正常則表示可以繼續運作了。
                                                        

　　If the concrete in the mixer has set, it is recommended to use the "air cannon" to break the concrete already set, and then shovel it out a little bit! Usually, the lower part of the tank body needs to be cut open, and then a cover tightened with a compass is added. This cover is used to open the air and discharge materials in case of emergency. In the process of pouring, people need to ventilate inside the tank. A fan should be placed at the entrance of the charging tank to blow in. When the "air cannon" works, it will generate dust, and it is necessary to connect the water pipe to wet and smash the concrete. After the concrete in the tank is broken and shoveled out, the cut part shall be welded, the cover shall be closed up and filled with water to test whether the rotation can be normal, and then a small amount of loading shall be increased to see whether the hydraulic press can work normally. If everything is normal, it means that it can continue to operate.

　　方法二：電焊或氣割

　　Method 2: electric welding or gas cutting

　　混凝土凝固后，其主要成分是硅酸二鈣、硅酸三鈣。理論上講，鹽酸可以與之反應解除其固態形狀。由于攪拌機的料口很小，鹽酸量難以控制，且鹽酸也可以與攪拌機罐體發生反應，所以操作很難實現。實踐中一旦出現這種情況，往往需要用電焊或氣割切開罐體，然后將凝固的混凝土機械破碎。

　　After concrete solidification, its main components are dicalcium silicate and tricalcium silicate. In theory, hydrochloric acid can react with it to remove its solid shape. Because the mixer's mouth is very small, the amount of hydrochloric acid is difficult to control, and hydrochloric acid can also react with the mixer tank, so the operation is difficult to achieve. Once this happens in practice, it is often necessary to cut the tank with electric welding or gas cutting, and then the solidified concrete will be mechanically broken.

　　混凝土結塊或者凝固在罐體內，會對攪拌機造成很大的傷害，攪拌機的混凝土凝固了怎么處理？通過以上介紹，相信廣大用戶對這個問題已經有所了解。如果您還想繼續了解其相關常識，可以訪問中科聚峰攪拌機http://m.zvmc.cn網站詳細了解，歡迎網站留言。

　　Concrete caking or solidification in the tank will cause great damage to the mixer. How to deal with the concrete solidification of the mixer? Through the above introduction, I believe that the majority of users have understood this problem. If you want to know more about it, you can visit Zhongke Jufeng mixer http://m.zvmc.cn Official website for more information, welcome to leave a message.